The best candidates for fast burn conversion are spark ignited piston engines with adjustable spark timing. Those with carburetors as original equipment do not have computers that control additional automotive functions besides fuel metering and spark timing. The fast burn engine can’t use computer management as a low cost conversion option. If an idle circuit similar to that of a carburetor is added to a fuel 1톤용기 throttle body as a spacer plate,Alternative Energy Series Fast Burn Conversion Articles a throttle body might be able to serve as a basic carburetor for cold vapor fuel. Many modern fuel injected engines can be owner retrofitted with carburetors and aftermarket or used factory intake manifolds for use with carburetors.
The traditional multi circuit carburetor is not required for vapor fuel, but is less expensive than producing new twin circuit carburetors designed specifically for vapor fuel. All carburetor air vents should be plugged so engine vacuum signals draw only from the unvented carburetor fuel bowl, which is connected to the fuel bubbler in the tank or racing fuel cell. The fuel float and needle valve assembly is removed. Any accelerator pump is removed and the enrichment hole is plugged. In carburetors that use vacuum power valves, such can be used to fine tune vapor flow according to vacuum signals. The idle circuit must retain adjustment from barely open to wide open.
Rod and jet enrichment systems such as used on Carter and Rochester carburetors can also be used to fine tune vapor mixtures. Go as lean as you can without the engine stumbling under load on the power circuit and richen slightly for best throttle response. If the max power metering is sufficient with selected main jets, which flow much more vapor than liquid, we can regulate the maximum fuel supply by means of an adjustable valve in the supply line. Start the fast burn engine with the idle mixture screw open wide and quickly close it after the engine starts. Back the adjustment screw off one turn after you stall the engine for lack of idle fuel. Too much idle fuel could melt engine parts as easily as too much fuel in the power circuit. If we never meter more fuel than can burn in half a power stroke, we avoid meltdown while maximizing power and fuel economy, minimizing exhaust emissions.
With fast burn, we want to retard initial spark timing to between sixty and eighty degrees after top dead center. On a V-8 we can move each wire in the distributor cap forward one position on the cap in the direction of rotor rotation. This will retard timing 90 degrees from the standard initial timing. A timing light on the number 8 cylinder will allow you to set initial timing with the stock timing marks. Setting number 8 cylinder for ten degrees advance would have number one cylinder firing at 80 degrees after top dead center. 20 degrees advance would have number one firing at 70 degrees ATDC, etc. An aftermarket timing tape, when available, is another way to accurately set spark timing. Otherwise, one can remove the crankshaft dampener or pulley with timing marks, measure the circumference, divide by 4 and mark at 90 degrees ATDC, 85, 80, 75, 70, 65, and 60 degrees. Marking all the way back to 30 degrees ATDC is a good idea. This is the most advance likely practical for max fast burn power and allows one to check for total mechanical or electronic spark advance. Optimum timing for best performance and economy, like fuel mixture, must be worked out by road testing the converted vehicle.
Fully vaporized fuel is likely to be combustible over a wide range of air/fuel ratios. As a safety precaution it makes sense to install a PCV valve or something similar. Should a timing chain let go or an intake valve bend, we don’t want fire in the intake manifold to find its way back to our bubbler and explode it. Better that a fuel supply line disconnect or rupture under the hood from combustion back pressure.
The bubbler where our vapor is made by engine vacuum, is a modified fuel tank or racing fuel cell. Our tank/cell must be vented to atmosphere. We want our air pick up filtered with something like a lawnmower air filter and mounted higher in or outside the vehicle, than the outside of the fuel filler tube, which is the most convenient place to tap our tank/cell for a very rich vapor.
On the typical fuel tank, our air vent can be easily installed where the original fuel supply line attached. We want another PCV valve near our air supply filter to seal the tank from atmosphere when the vehicle is not running and the tank/cell is pressurized by atmospheric heat. Gas expansion in our tank now moves fuel through the carburetor into the intake system, where it allows instant starts, as with fuel injection.
Bubbler design is guesswork. Whatever supplies the most consistent air/vapor mixtures from a tank 3/4, 1/2, 1/4 and 1/8 full, is what we want. Variations in vapor from the tank will make engine tuning difficult and variable. Consistent mixture from the bubbler is important. If the air supply is opposite the vapor supply line, we would expect a richer vapor than if the air supply line was near the vapor supply line. We want the air supply line to lie on the bottom of the tank, below whatever fuel we have. We never want the fuel tank full, so a drain in the air supply line will be handy for accurately checking fuel economy. You add ten gallons to an empty tank and drive until a working fuel gauge goes below 1/4 tank and you then drain the remaining fuel from the tank into gallon jugs. Subtract the remaining fuel from the ten gallons you started with. Divide the gallons used, into the miles driven and we will know our MPG.
We never want to fill our fuel tank to filler nozzle shut off, as that would give us a minimal surface area from which to vaporize our fuel and our mixture could then be too lean to run our engine. However, if one wanted to build a vapor chamber and install it above the top of the fuel tank and filler tube, there might not be much difference when the tank is overfilled. One thing we definitely want to avoid is liquid fuel in our vapor supply line. Though it is unlikely the liquid fuel would reach the carburetor, the more it wet the vapor supply line, the richer the mixture would be at the carburetor.
I envisioned a tri Y air bubbler on the fuel tank floor, to evenly distribute air in the tank. The line connecting to the old fuel supply line, inside the tank would split into two equal length lines of the same diameter from a Y or T connector. The two lines are then split into two more equal length tubes (fuel proof, of course) and porous air bubblers to make small bubbles moving through the fuel. This would give us a richer mixture at the fuel supply line, than a single tube with no air diffusers. I would terminate my air supply lines with those bronze fuel filters many carburetors used just ahead of the needle and seat assembly at the end of the supply line. Short term tests I did several years ago showed that the ceramic bubbler filter for fish aquariums gave very fine air bubbles and did not seriously deteriorate in gasoline. They were not very expensive.
I can only guess at supply line sizes. My guess is that the filtered air supply line need be no more than a quarter inch ID. The vapor supply line probably needs to be no greater than three eighths inch ID.These are the basics of a cold vapor, fast burn fuel system. I would expect improvements to come rapidly following road testing. When we know the typical optimum spark timing and air/fuel mixtures, we can apply this knowledge to small engines with fixed spark timing, like lawn mowers, snow blowers and electrical power generators.
My expectations of fast burn performance is between two and three horsepower per cubic inch displacement, which would make fast burn conversion the best power bang for the dollar. No other modification can come close in dollar costs. Under most racing rules, fast burn would be legal for the allowed fuel and add more power than supercharging or nitrous oxide injection. Yet, these power boosters will add a lot more power to a fast burn engine than to a slow burn engine. Hence, the fast burn conversion will out perform slow burn by a wide margin, regardless of class allowed modifications. The fast burn conversion can also be camouflaged to look stock by plumbing the supply line through a non functional fuel pump.
As to economy, Charles Pogue exceeded 200 MPG with his hot vapor, ‘37 V-8 Ford, which would rarely yield 20 MPG in slow burn configuration. Uniform cold vapor might have allowed him to achieve the 300 MPG economy he was shooting for, while more than doubling stock power output. When fast burn conversions become common, performance and economy contests will lead to rapid improvements in the very simple technology.
